Non-Hazardous Ink and Graffiti Remover
Description and Use
Graf-Ex is a multiple purpose modern safe stripper designed to be used where safety and performance are of equal importance. Graf-Ex is in fact an outstanding performer, safely removing ink and paint from painted surfaces and fiberglass. Graf-Ex is non-flammable and biodegradable. This product was designed to be used in environments where it is important to not damage the substrate. Examples of this would be school restrooms, bank ATM machines, adhesive on trucks, building interiors, painted exteriors, and portable potties at job sites. Graf-Ex does not harm most substrates. It will not raise the grain of wood, cause flash rusting in metal, or damage fiberglass surfaces. Water can be used to rinse and will stop the activity of the product.
Advantages
*Safe, biodegradable, effective
* It will not raise the grain of wood, cause flash rusting in metal, or damage fiberglass surfaces.
Limitations
*GRAF-EX will not work on epoxy or urethane type coatings.
* Do not use on Plexiglas. (Use Plexi-Clean)
Technical Data
Appearance & Odor: White to yellow over time, mild citrus odor.
Physical State: liquid
pH: 7.5
Vapor Pressure (mmHg): N/A
Vapor Density (air=1): N/A
Boiling Point: 212 °F
Freezing/Melting Point: N/A
Specific Gravity (WATER =1): 0.900
Evaporation Rate: N/A
Solubility in Water: Complete, stable emulsion
Preparation
Protect:
Test and protect adjacent and surrounding surfaces from exposure to the cleaning solution.
Surface & Air Temperatures
Do not clean when temperatures are below freezing or will be overnight. Best cleaning results are obtained when air and masonry surface temperatures are 40° Fahrenheit or above. If freezing conditions exist prior to application, allow adequate time for masonry to thaw.
Pre-Testing
Always test prior to beginning full-scale cleaning operations. Testing should confirm cleaning effectiveness on each type of surface and stain designated to be cleaned. Test also to determine the desired surface contact time and any potential for adverse reactions with adjacent materials. Allow test panels to dry thoroughly before evaluating final appearance and results.
Dilutions
Use Graf-ex undiluted
Application Instructions
Use Graf-ex undiluted and apply with either a low-pressure spray unit or wipe it on with a cloth. Spray the product on from the top down and with a side-to-side overlapping motion. Often just a wipe with a damp cloth is all that is necessary to remove the paint or ink. As with all strippers proper testing of the material or the coating to be stripped is the only way to determine the correct procedure. Basic guidelines would be that the material works better at an ambient temperature in the 70° Fahrenheit range. Sometimes two applications one following the other after a short soak period will out perform a single application and mechanical removal. The material is water thin and penetrates extremely quickly to soften inks or paints. Dwell times will vary with thickness of the coating to be stripped but GRAF-EX can remove many materials in a fifteen-minute time span. Pressure washer rinsing on masonry or stone with at least 1500 psi is recommended for best results.
Coverage Rates
Coverage rates will vary from 100 - 250 sq. ft./gal depending on the surface porosity, texture and severity of staining.
Safety Information
*Precautionary Measures:
Proper ventilation should always be a consideration when long-term exposure will occur. It is recommended that skin contact be kept to a minimum and at least a water rinse be used after contact. Always wear goggles and gloves when handling this product. Keep off of skin and clothing. If material comes in contact with clothing, wash before reuse. Contains Hydrocarbon blend naphtha. Do not get in eyes, on skin or clothing. Avoid breathing fumes. Keep container closed when not in use. Use with adequate ventilation. Applicators should wear boots and gloves, face shields and/or goggles made out of solvent resistant materials to avoid splash to bare skin or eyes and MIOSH/MSHA approved respiration if over PEL and adequate ventilation is not provided. Take precautions to avoid exposing building occupants to Graf-Ex odor if it becomes a problem. Dispose of empty containers according to federal, state and local requirements. Avoid drifting of material or rinse water onto autos and pedestrians by protecting or diverting such traffic. Do not dilute Graf-Ex with any other product. Do not use for any other applications other than specified. Do not remove label. Read Material Safety Data Sheet for additional safety and health hazard information prior to use.
*First Aid +
Instructions in Case of Contact or Exposure Skin & Eye Contact:
Eyes: Flood with water for 15 minutes, If irritation persists, call physician.
Skin: Wash off with soap and water, If irritation develops call physician
Inhalation: Do not induce vomiting. Seek immediate medical attention
Ingestion: Remove to fresh air. If irritation develops, call physician.
Spill or Leak Procedures
Waste Disposal Method: Check state, local or federal regulations for your area. Steps to be taken if material is released or spilled: Large spill; dike and contain for intended use. Small spill; absorb on oil dry and place in approved container for disposal.
Container Handling/Storage
Store in a cool dry place. Vent bung before opening. Keep container tightly closed when not in use. Do not use pressure to empty container. Wash thoroughly after handling. Do not use container as dilution or rinsing vessel. Empty containers retain residue and should be handled as if full.
Notice
This product has been classified in accordance with the hazard criteria of the CFR.
Disclaimer
The information herein is given in good faith, but no warranty, either expressed or implied is made. Final determination of the suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein we cannot be sure or guarantee these are the only hazards, which exist.